Restaurant no hot water violations, explained for plumbers
A restaurant no hot water violation means the inspector found that a required fixture was not getting an adequate hot water supply. That often looks like no hot water at a handwash sink, water that is not hot enough, a mixing valve that cannot temper the water, or a warewashing sink that has gone cold. A recent citation is a clear signal that the kitchen may need a plumber for a water heater, a mixing valve or a supply problem.
For leaks, clogged drains and the rest of the list, see the restaurant plumbing violations guide. For vacuum breakers and air gaps, see restaurant backflow violations. To pull a local list, go to plumbing reports.
What inspectors write up
Common inspection notes include no hot water at a handwash sink, water that does not reach the required temperature, a faucet that does not work, or no hot water at a warewashing or three-compartment sink.
The FDA Food Code 2022, Chapter 5, is the model many local codes follow. Three sections matter most:
- 5-103.11 Capacity. The water source and system must meet peak water demand. Hot water generation and distribution systems must meet peak hot water demand throughout the food establishment. A heater or distribution problem can show up at handwash sinks and warewashing sinks on the same visit.
- 5-103.12 Pressure. Water under pressure must be provided to all fixtures, equipment, and nonfood equipment that are required to use water, with limited exceptions for temporary operations or a temporary interruption of the water supply.
- 5-202.12 Handwashing Sink, Installation. A handwashing sink must be equipped to provide water at a temperature of at least 29.4 C (85 F) through a mixing valve or combination faucet. A steam mixing valve may not be used at a handwashing sink.
Local wording often tracks that model. In Georgia, which includes the CleanPlate plumbing areas of Fulton, Cobb and Gwinnett counties, Rule 511-6-1-.06 requires tempered water at a handwashing sink of at least 85 F (29.4 C) through a mixing valve or combination faucet, and requires hot water systems to meet peak demand throughout the establishment. Section numbers and temperatures can still differ by city, so read the inspector's note before you bid. The 2022 Food Code figure at the handwashing sink is 85 F, not a higher number from an older edition.
Why this is urgent plumbing work
Staff still have to wash hands and wash ware. The kitchen may still be open, but the owner has a written finding that often points to a water heater, a mixing valve or combination faucet, or a supply and pressure problem. That is licensed plumbing work. Name the fixture the inspector cited, and confirm the need before you bid.
Reinspection timing is set by the health department and by the overall result of the visit, not by a separate "no hot water day count." Two covered-area examples of published follow-up windows:
- City of Dallas, TX. Dallas Consumer Health publishes a score interpretation guide: score 100 to 80 meets standards; 79 to 70, follow-up within 30 days; 69 to 60, follow-up within 10 days; 59 and below, follow-up within 24 hours. A no-hot-water finding does not automatically land in one of those bands. If the visit score does, that published window applies.
- Georgia (Fulton, Cobb, Gwinnett). Georgia DPH Rule 511-6-1-.10 says follow-up inspections must be conducted within ten days after an establishment receives a grade "U". A follow-up is also a complete inspection after a routine grade of "C" or "U". If a venue is graded "U" and does not earn at least a "C" within ten days, it may be asked to close voluntarily or have its permit suspended or revoked.
Other covered areas may set a correction date on the report or may not publish a fixed day count. Do not assume Dallas or Georgia timing applies somewhere else.
What CleanPlate counts, and how the report works
CleanPlate plumbing reports are built from public health inspections. Only the inspector's written observation is read, never a checklist title alone.
Counted findings include leaks, clogs, slow or backed up drains, missing hot water, and sinks, faucets or toilets out of order. A missing vacuum breaker, backflow device or air gap is counted separately. Dispensers, signage, thawing practices, grease trap odors and door gaps are not counted.
Findings the source marks as corrected on site, or that the inspector says were repaired during the visit, are left out. Some sources rarely record corrections, so a listed problem may already be fixed. Known latest closure results are excluded.
To get the list:
- Pick your area on the plumbing page.
- Preview the count. You will see how many venues qualify and up to five of them.
- Buy the full report. The full report is $29.99. You get a PDF for one covered area with at least 25 cited venues, each qualifying citation, a ZIP breakdown and a link to each venue's CleanPlate record.
The report window starts at the last 30 days and extends to 60 or 90 days if needed to reach 25 venues. You will see the actual window and the mix of issues.
If you want ongoing leads, reply about a weekly emailed brief of new local inspections with plumbing problems. That brief is paid monthly. Pricing is set when you ask.
The report is a prospecting aid. It shows what an inspector wrote on a given day. It does not confirm current condition, who services the building, who to contact or whether the owner wants to buy. Later inspections are shown when we have them, but a later visit does not prove the problem was fixed. Confirm current need before outreach.
Where CleanPlate covers plumbing
CleanPlate plumbing reports cover 15 areas: Miami-Dade, Broward and Palm Beach counties in Florida; the City of Dallas and Tarrant County Health in Texas; Chicago, Illinois; Kansas City, Jackson County Health and the City of St. Louis in Missouri; Fulton, Cobb and Gwinnett counties in Georgia; and Polk, Linn and Scott counties in Iowa.
New York City is not covered for plumbing. How often the data refreshes depends on the area, anywhere from nightly to monthly. Chicago inspection data is modified for use from its original source, www.cityofchicago.org, and the City of Chicago makes no claims about its content, accuracy, timeliness or completeness.
FAQ
What is a restaurant no hot water violation?
A finding that a required fixture, most often a handwash or warewashing sink, did not have an adequate hot water supply.
What temperature does the FDA Food Code require at a handwashing sink?
FDA Food Code 2022 section 5-202.12 requires at least 29.4 C (85 F) through a mixing valve or combination faucet. Local codes can differ.
Is a no hot water citation plumbing work?
Usually yes: a water heater, a mixing valve or combination faucet, or a supply and pressure problem. Dispensers, signs, thawing practices, grease trap odors and door gaps are not counted.
Which areas does CleanPlate cover for plumbing?
The 15 areas listed above. New York City is not covered for plumbing.
What is in the full plumbing report?
A PDF for one covered area with at least 25 cited venues, each qualifying citation, a ZIP breakdown and a link to each venue's CleanPlate record. The preview is free. The full report is $29.99.
Is the weekly email separate from the report?
Yes. The full area report is $29.99 once. A weekly emailed brief of new local plumbing inspections is paid monthly. Pricing for the brief is set when you reply about it.
See who was cited near you
Pick your county, see how many venues were cited for plumbing problems (including missing hot water) and preview five of them for free. The full report is $29.99. For ongoing leads, ask about the weekly plumbing brief.
See your area · Restaurant plumbing violations guide · Restaurant backflow violations
Sources
- FDA Food Code 2022 landing page
- FDA Food Code 2022, Chapter 5 (Water, Plumbing, and Waste) PDF mirror (sections 5-103.11, 5-103.12, 5-202.12)
- Ga. Comp. R. & Regs. R. 511-6-1-.06 (handwashing sink temperature and hot water capacity; applies in Fulton, Cobb and Gwinnett)
- City of Dallas, Restaurant Food Establishment Scores
- Ga. Comp. R. & Regs. R. 511-6-1-.10